Step 2: Turn on your soldering iron and let it heat up. Step 3: Wipe the tip of the soldering iron on a damp wet sponge to clean it. Wait a few seconds to let the tip heat up again before proceeding to step 4. Step 4: Hold the soldering iron in one hand and solder in the other. Touch the solder to the tip of the iron and make sure the solder flows evenly around the tip.
You should tin the tip of your iron before and after each soldering session to extend its life. Eventually, every tip will wear out and will need replacing when it becomes rough or pitted.
This will help the component make a better connection with the copper pad and prevent it from falling out while soldering. At this point, touch the tip of the iron to the copper pad and the resistor lead at the same time. You need to hold the soldering iron in place for seconds in order to heat the pad and the lead.
Step 3: Apply Solder To Joint — Continue holding the soldering iron on the copper pad and the lead and touch your solder to the joint. If the joint is too cold, it will form a bad connection. Step 4: Snip The Leads — Remove the soldering iron and let the solder cool down naturally. Once cool, you can snip the extra wire from leads. A proper solder joint is smooth, shiny and looks like a volcano or cone shape.
You want just enough solder to cover the entire joint but not too much so it becomes a ball or spills to a nearby lead or joint. Begin by removing the insulation from the ends of both wires you are soldering together.
If the wire is stranded, twist the strands together with your fingers. Make sure your soldering iron is fully heated and touch the tip to the end of one of the wires. Hold it on the wire for seconds. Repeat this process on the other wire. Hold the two tinned wires on top of each other and touch the soldering iron to both wires.
This process should melt the solder and coat both wires evenly. Remove the soldering iron and wait a few seconds to let the soldered connection cool and harden. Use heat shrink to cover the connection. The good thing about using solder is the fact that it can be removed easily in a technique known as desoldering. This comes in handy if you need to remove a component or make a correction to your electronic circuit.
To desolder a joint, you will need solder wick which is also known as desoldering braid. Step 2 — Heat your soldering iron and touch the tip to the top of the braid. This will heat the solder below which will then be absorbed into the desoldering braid. You can now remove the braid to see the solder has been extracted and removed. Be careful touching the braid when you are heating it because it will get hot.
Optional — If you have a lot of solder you want removed, you may want to use a device called a solder sucker. This is a handheld mechanical vacuum that sucks up hot solder with a press of a button.
To use, press the plunger down at the end of the solder sucker. Heat the joint with your soldering iron and place the tip of the solder sucker over the hot solder. Press the release button to suck up the liquid solder. In order to empty the solder sucker, press down on the plunger. We truly believe that adding a makerspace to a school or library can help students acquire the skills needed for the 21st century.
Copyright Makerspaces. Soldering Iron A soldering iron is a hand tool that plugs into a standard v AC outlet and heats up in order to melt solder around electrical connections. Soldering Station A soldering station is a more advanced version of the basic standalone soldering pen. Soldering Iron Tips At the end of most soldering irons is an interchangeable part known as a soldering tip. Image Credit — Sparkfun.
Soldering Iron Stand A soldering iron stand is very basic but very useful and handy to have. Solder Solder is a metal alloy material that is melted to create a permanent bond between electrical parts. For many reasons, the Weller WE soldering station is a smart soldering solution for several different types of jobs. If you want a powerful tool that gets the job done quickly and reliably, try the WE This unit has many advantages, but some of its main draws are its:. The collection of technical specifications that the WENA offers is a huge part of what makes it such as powerful soldering solution.
Its specs are as follows:. If you want a powerful yet versatile soldering station at an affordable price point, WENA is hard to beat. With top-of-the-line performance, ease of use, safety features and affordability, it's the perfect soldering solution for a wide range of jobs. See Product Details. Overview Technical Data Benefits.
The iron's faster heat up and recovery time gets the job done quicker with more efficiency and precision Easy to handle high performance iron Intuitive navigation Low total cost of ownership. Maximum Protection ESD-safe station, iron, and heat-resistant silicon cable for safe handling Reinforced safety rest for secure iron storage Temperature stability and temperature lock protects tips and components, affording a consistently high quality Process with repeatable soldering results Standby mode and auto setback conserves energy, protects equipment Password-protected to preserve settings.
Power unit, 1 channel with soldering iron WEP 70 and safety rest PH 70 70W solder iron with ergonomic handle and providing toolless tip change ESD safe station, iron and heat-resistant silicon cable for safe handling Using ET soldering tips Standby mode and auto setback conserves energy, protects equipment Password-protected to preserve settings.
Weller WE The latest addition to our WE Line is a powerful yet easy-to-use and cost-effective digital soldering station that comes ready to meet the requirements of a range of soldering jobs. What Does It Come With? This range allows you to get the job done, and the long life of the tips helps to keep costs low. We recommend using genuine Weller ET series tips. Who Is It For? Professional Use: The WE is an ideal tool for commercial and industrial uses because of its professional quality.
Experienced craftsmen will not be disappointed with the performance of this professional soldering iron kit. It meets and even exceeds many of the standards and specifications that professionals would expect from any comparable soldering station.
It empowers you to reliably and efficiently produce high-quality results. This consistent quality will improve your professional reputation, and the new efficiencies you can achieve will help your business run smoothly. Education and Training: This latest addition to the WE product line is also a good soldering iron pencil for education and training in settings such as colleges, tech schools, and even high schools. It's easy to use and features numerous safety features that will help prevent incidents in the classroom or during on-the-job soldering iron training while at the same time helping students to learn practical skills.
Its relatively small size and light weight also help make it easy to manage in a classroom environment. Beginners and Hobbyists: This unit is also a good entry-level soldering iron kit, so it's even suitable for hobbyists and DIY enthusiasts. Its affordability, ease of use and safety features make it easy for anyone to use it with only basic orientation and a review of safety considerations. We recommend using this tool for applications such as the following: Recommended: We recommend using this product for relatively easy professional soldering jobs, including work on electronic kits and printed circuit board soldering.
The tool is also useful for cable assembly and working on indoor lighting, and it's ideal for use in educational and training settings. Acceptable: The following are acceptable uses of the WE , and while these options aren't as ideal for this system as the recommended applications, it can still produce satisfactory results.
You can use this tool for small appliances, small engines, electrical projects and audio systems. It's also useful for hobby models and crafts, especially if you're looking for the best affordable soldering station that still provides a considerable amount of power and number of features. Not recommend: We do not recommend using this product for micro-components, metal art, jewelry, heat sinks, ground planes or automotive or marine work.
This unit has many advantages, but some of its main draws are its: Power: With the WENA digital soldering station, you'll have exceptional power to get the job done fast. As the most powerful soldering station in its class, the V, 70W power station helps you work efficiently, reliably and precisely.
Ease of use: The WE is extraordinarily user-friendly. The controls are designed to be intuitive, and the iron features an ergonomic design that's easier to control. The power station features an easy-to-read LCD screen, three push buttons and a power switch on the front of the unit. The iron is lightweight and features a pencil design that makes for comfort and easy maneuvering. Precision: When you use this product, you'll be able to more easily deliver consistently high-quality results.
The smooth handling and control that the WEP 70 soldering iron offers and its user-friendly controls contribute to this quality. The excellent temperature stability and accuracy of the unit have a significant impact as well.
Additionally, you can use a range of tips and temperatures to reliably get the exact results you need. Safety: WENA has numerous features that will reduce potential hazards throughout your workday. It features a reinforced safety rest that provides extra stability when storing the iron between uses. The cables of the iron are also heat-resistant and meet industry standards for mechanical strength. Cost efficiency: Despite having all of these incredible features, the WE is an extremely cost-effective tool.
It's an affordable soldering iron overall and also contains elements meant to help you save money as you use it. The ET tips that the iron uses have an extremely long life, which significantly reduces operational costs. It also has a standby mode that the iron automatically enters into when not in use, which helps reduce energy use and further extend the life of your tips.
The WE soldering station includes the following features and benefits: 70W power station: WENA features a watt W power station that gives you the power you need to consistently produce high-quality results. This increased power heats up the iron faster and also provides faster recovery time, which enables you to work more efficiently and precisely.
This powerful tool is capable of reaching high temperatures but is also lightweight, allowing for increased control over your work. It's designed in the soldering pencil style and enables highly precise soldering.
Toolless tip change: The soldering iron also makes it easy to change tips. You don't even need any additional tools to do so.
You can quickly change out hot tips by turning the plastic knurled nut located on the soldering pencil by hand.
0コメント